SJRWMD slide 1 SJRWMD slide 2 SJRWMD slide 3 SJRWMD slide 4 SJRWMD slide 5 SJRWMD slide 6
SJRWMD logo for print -

Water conservation

Irrigation maintenance

Irrigation can be done in two basic ways — with a hose and sprinkler or with an inground irrigation system.

Woman placing a sprinkler in her yard

When using a hose and sprinkler, place the sprinkler in the area that is driest. Allow the sprinkler to run the proper length of time to apply no more than three-quarters of an inch of water. When that area is complete, move the sprinkler to another dry area. Place the sprinkler so that its water spray will overlap the area previously watered. Position the sprinkler so that your water lands on the lawn and shrubs, not on paved areas.

Inground irrigation systems can be automatic or manual, or a combination. The automatic system is set for a predetermined time of day and days of the week. Make sure it is set to follow the watering restrictions. Learn how to operate your system. Check timing devices regularly to make sure they are operating properly. Watch for broken or misdirected sprinklers. During extended periods of rainy weather, irrigation systems should be turned off.

Automatic inground irrigation systems have become a common method for watering our lawns. Unfortunately, many of these irrigation systems are inefficient. Sometimes as much as half of the water delivered through the systems doesn’t benefit the intended plants.

We can have a tremendous impact on the amount of water we use outdoors by using well-designed irrigation systems and performing regular maintenance to keep them functioning properly.

Install sprinklers that are the most water efficient for each use. Rotors and spray heads are good for turf areas, but don’t use both in the same zone. For even distribution, flow rates must be consistent throughout the zone. In planting beds, use micro-irrigation, which includes drip and soaker hoses. Also, use spray heads designed for planting beds. Position the sprinkler so that you water only the lawn and shrubs, not paved areas.

Maintain your irrigation system. Watch for broken or misdirected sprinklers. Check for leaks and clogged spray heads. Soft, wet spots around the sprinkler could indicate a leak is being absorbed into the ground.

A rain sensor attached to a mounting bracket

Florida law requires that all automatic irrigation systems installed after May 1991 have a functioning rain sensor shut-off switch. This switch overrides the automatic irrigation system’s cycle when a preset amount of rain has fallen. The switch can be adjusted for different amounts of rainfall. To ensure proper functioning, the sensor should not be installed in an area that is blocked by roof overhangs, bushes or trees. Check regularly to make sure the system is working properly.

Backflow prevention devices are also necessary to prevent water from flowing back into the water main, which can contaminate drinking water.

With Florida’s irrigation laws continually being updated, you should consult with or hire a certified professional to design and install an irrigation system. Certified professionals can be found by contacting such organizations as:

Irrigation system design

A landscape and an irrigation system should be designed so that they work well together. This means putting your plants in “irrigation zones,” allowing for a system design that will deliver the appropriate amount of water to individual planting beds or turf areas.

You should:

  • Keep non-turf plants confined to planting beds.
  • Group together plants that have similar moisture needs.
A house and yard diagram for planning sprinkler placement and water coverage

Irrigation zones — For efficient irrigation, zones are critical. Each irrigation zone should be composed of the same kind of emitters throughout, be it rotors, spray heads or micro-irrigation. The rate at which different heads deliver water varies, so for even coverage, head types should not be mixed. Also, heads from different manufacturers vary in coverage, so all heads should be the same brand to ensure even coverage.

The term “head-to-head coverage” is used to describe proper placement of sprinkler heads to ensure even water coverage. Essentially, the water from one head should reach the closest neighboring heads.

If one type of head in a zone delivers one inch of water in one hour and another type only delivers one-quarter inch, then you may be overwatering one area or underwatering the other. For example, use rotors or pop-up spray heads for turf areas, but don’t use both in the same zone.

Other considerations include:

  • Use gear-driven rotors to water large turf areas.
  • Use spray heads to water medium- to small-sized turf areas.
  • Use micro-irrigation to water planting beds. Because it is a low-volume irrigation technique, micro-irrigation uses less water than rotors and spray heads. Micro-irrigation systems include trickle or drip, micro-sprays (also known as micro-jets) and bubblers.
  • Use drip and trickle irrigation on shrubbery and in planting beds.
  • Use micro-sprays and micro-jets for shrubbery or ground covers.
  • Use bubblers to establish trees or large shrubs.

Head placement — Spray head placement is just as important as the type of head used in the various zones of your irrigation system.

Hand installing the correct spray head for the relevant application

Spray heads should have sufficiently large bodies so that they are above the normal turf level when spraying water. For example, six-inch spray heads are required to adequately clear properly mowed St. Augustine turf. Without proper maintenance, spray heads can become too low to the ground to be effective. Use six-inch pop-up riser extensions and periodically raise spray heads above grass beds.

Heads should be adjusted to prevent water from spraying onto roads and driveways and to prevent water from spraying onto houses or other obstructions.

Pressures and piping — Adequate pressure must be factored through the entire system, from the water source to the last head on the line. Increases in pressure can occur by improper design, such as by using pipe that is too small. Too much pressure in pipes can cause leaks by wearing down pipes and fittings.

Generally, pressure differences within any irrigation zone should be no more than 20 percent. For example, if pressure at the source is 60 pounds per square inch, or 60 psi, pressure throughout the system should not fall below 48 psi.

Low pressure is apparent when heads emit large droplets, which can cause erosion and runoff. Too much pressure can result in heads misting, allowing water to drift away.

For correct pressure, pipe size is fundamental. Pipes that are too small will account for large differences in pressure, resulting in uneven water application.

Controls and switches — Most irrigation system timers, also known as controllers, allow a great level of control over watering schedules. Familiarize yourself with your timer’s functions using the instruction manual it came with. Often, controllers also have directions on the inside of the cover panel. The following describes the programming controls in the photograph, which represents a typical controller:

An automatic irrigation system timer
  • LCD display — During normal operations, this displays the time of day; during programming, it shows the results of your commands; during watering, it shows the station that is running and the minutes remaining in its run time.
  • Arrow on/off buttons — These set times and days to water, and make program changes.
  • A/B program button — This selects watering program A or B.
  • Manual start/advance button — This starts the irrigation program manually or manually advances watering from one station to the next.
  • Programming dial — This turns the controller on and off, and is used for programming.
  • Schedule slide switch — This selects one of the fixed-interval watering schedules for a custom watering schedule.

Program elements — Timers generally have three criteria that need to be set: watering days, start time and watering duration.

What days the system waters will need to be changed seasonally.

“Start times” refer to the time of day the first zone will begin watering, followed by the other zones in sequence. Remember to set your system to operate before 10 a.m. or after 4 p.m.

Watering duration — The number of minutes that each zone runs — depends on the type of head used in each zone. Three-quarters of an inch of water is enough to replenish the grass.

Moderate amounts of water can create a healthy, drought-and stress-tolerant lawn. Applying no more than three-quarters of an inch of water is enough to replenish the grass.


  • Rotor zones set between 45 and 60 minutes apply about three-quarters to an inch of water.
  • Zones with spray heads set at 20 to 35 minutes generally apply the same amount.
  • For newly installed planting beds, set micro-irrigation zones for 60 minutes twice a week for 30 days. Then cut back to once a week until plants are established, which will take no more than another month or two, depending on weather conditions. Then water only as needed.

Other considerations — The following factors should also be considered when scheduling irrigation systems:

  • During extended periods of rainy weather, irrigation systems should be turned off.
  • Irrigation controllers have default programs that take over if a set program is lost due to a power outage. On some controllers if the schedule switch is in the “Custom” mode, it will default to watering every day. Reset program after a power outage.
A man adjusting a sprinkler so as to avoid overspray on a sidewalk

For an irrigation system to function efficiently, regular maintenance is required. Just as you routinely rotate the tires and change the oil of your car, you must also inspect and adjust your irrigation system for it to work properly. You should:

  • Turn the system on occasionally during daylight hours to observe the heads during irrigation and to check for broken or misdirected spray heads.
  • Periodically raise rotors and spray heads above grass beds because foot and mower traffic tend to push them into the soil.
  • Buy and install riser extensions as ground covers grow or grass thickens at the base. These keep spray heads above grass beds.
  • Replace or clean micro-spray heads if they are clogged.
  • Adjust heads so they cover the target area and don’t waste water on tree trunks or sidewalks.
  • Clean micro-irrigation filters as needed. Filtration is necessary to prevent spray emitters from getting clogged.
  • Use only replacement parts produced by the same manufacturer, as different brands often don’t match up correctly.


In this section
More about


Governing Board meetings
Please see agendas for specific meeting times, which may differ monthly.

Lobbyist registration requirements

Other district meetings and notices

Central Florida Water Initiative

Tell us how
we are doing.

Take our survey on
customer service.

By accessing this site, you agree to accept terms and conditions of the district’s liability disclaimer.

Employee Portal

St. Johns River Water Management District
4049 Reid Street, Palatka, FL 32177
(800) 725-5922